Hi, all! Been a while since I dropped by. I'm sorry I've been such a stranger. I was hoping to find some modification assistance.
I got this wonderful converter online from Raphnet via eBay that lets you use third parry Famicom controllers on an NES. For that purpose, it works great. Unfortunately, I did not read the fine print; it does not work wit other peripherals, such as the light gun, which is the purpose for which I bought it.
Does anyone know enough about the NES P2 and Famicom EXT port configurations to let me know what wires so need to put where for this to do what I want. The ability to use third party Famicom controllers on my NES is entirely useless to me, so if this change makes the two mutually exclusive, then so be it.
This will definitely be used in an upcoming Famicom Dojo video, and whoever is able to help the best will get direct credit (as well as this board as a whole). I could possibly even throw a t-shirt your way, depending on the sizes I have left! ;)
Thanks everyone for being so awesome for so long.
~Sean
Famicom extension is using a simple db15 connector and it shouldn't be very difficult. I did some research (I have not NES) and is quite easy.
Please look at this:
http://nesdev.com/zapper_to_famicom.txt
Since you have acces to wire of db15 is just to de-solder those cables and solder back to correct position as in the diagram in link. :) Link I sent is for NES gun on FC but is the exact same thing just you use FC Gun on NES.
Great, thanks! That's very close to what I need to fully do this on my own.
I'm still not sure which connector is which on the existing configuration. I suppose I could do some trial and error, but I don't want to fry my consoles.
If you have (or anyone has) a diagram on what the current configuration mapping must be so that I can translate to the one you provided, I would be most appreciative.
EDIT: Actually, now that I think about it, that might not be enough. Looking at the diagram and the photo, it's possible that the two are not mutually exclusive. It looks like the "o" wires are the same in both (one is the 5V, one is ground). It could well be that the two wires ("T" and "S") that haven't been hooked up are all I need to complete the circuit, and I can just leave the remaining three alone.
The only question would be which one is which. I might have access to a voltmeter.
EDIT 2: Okay, here we go! I think I am very nearly there.
I found this website:
http://chriskempson.com/posts/nes-controller-to-famicom-adapter/
Which linked back government this very forum:
http://www.famicomworld.com/forum/index.php?topic=3583.msg55602#msg55602
(I am attaching the diagram for the sake of posterity.)
If I'm reading this right, the adapters for P1 and P2 are indeed mutually exclusive; I need to remove pins 13 and 14 and connect them to 7 and 9 respectively. That should be easy since they are already hooked up, and I can just move them.
Step 2 is to hook up D4(2) to pin 4, and D3(2) to pin 5. Those are, by process of elimination, the two unused wires in photo 3. The trick is to figure out which wire is which, and if/when I have access to a voltmeter, I can do that.
Thanks, again! I'll report back with my findings.
~Sean
Here is link to diagram I think you using that adapter:
http://www5b.biglobe.ne.jp/~g-take/nfc.html
I don't know if you can read Japanese but I think is pretty self explanatory. But if you find a better source in English it's good for you. :)
This is for AV Famicom I think...I have not this system so I don't know, but I found another link with better description in English. Actually it seems it is the exact same seller you bought it from (Raphnet). If that's the case, then you got your original wiring right there.
http://www.raphnet.net/electronique/famicom_to_nes/index_en.php
Ah yes, just rewire them according to my first reply (that must be for 2P right?) and use Raphnet as original reference I think is the best for you. Good luck!
Excellent!!
Yeah, according to his website a third party controller might use different colors, and as I suspected that's what he used to create mine, because the wire colors in my photo are totally different. I'll still need a voltmeter to be 100% sure which is which. (Hey, I have a 50% chance otherwise, right?)
PM me or email your t-shirt size and an address, and I'll get that sent out this week!
Thanks again,
~Sean
Ah no problem! I live in Japan so shipping should be too expensive :-[ Please don't mind about that. I am just glad I could assist even though most of the finds were a result of searching the Internet.
Quote from: SeanOrange on March 11, 2018, 09:58:35 pm
If I'm reading this right, the adapters for P1 and P2 are indeed mutually exclusive; I need to remove pins 13 and 14 and connect them to 7 and 9 respectively.
I don't think that would do you any good. Light guns would work but Famicom controllers would stop working. Just let it be wired like P1 and add the extra two lines that the light gun are using (pin 4 and 5 in 133MHz's diagram). That way you can use it both as controller adapter and light gun adapter (including some other peripherals like the Famicom Arkanoid paddles and the Family Trainer if I remember correctly).
And yeah never trust color coding on wires, they are never the same between products. Use the continuity test on a multimeter.
The zapper use 7 wires all together,looks like your cord has 2 wires that are cut,if you can get those connected it should work.
I don't mind if it doesn't work as a P1 adapter anymore; if I'm that interested, I can always get another one.
I guess I don't know for sure if just connecting those two disconnected wires without moving the other two controller wires that are already connected will be enough. Maybe it will be? I can certainly try that first.
Quote from: Retrospectives on March 11, 2018, 11:02:19 pm
Ah no problem! I live in Japan so shipping should be too expensive :-[ Please don't mind about that. I am just glad I could assist even though most of the finds were a result of searching the Internet.
Ah, that doesn't bother me at all. But you'll get a shout out on the video once it's done, that's for sure!
Quote from: SeanOrange on March 14, 2018, 02:27:38 am
I don’t mind if it doesn’t work as a P1 adapter anymore; if I’m that interested, I can always get another one.
I guess I don’t know for sure if just connecting those two disconnected wires without moving the other two controller wires that are already connected will be enough. Maybe it will be? I can certainly try that first.
Quote from: Retrospectives on March 11, 2018, 11:02:19 pm
Ah no problem! I live in Japan so shipping should be too expensive :-[ Please don't mind about that. I am just glad I could assist even though most of the finds were a result of searching the Internet.
Ah, that doesn’t bother me at all. But you’ll get a shout out on the video once it’s done, that’s for sure!
Indeed. At least GND and 5+ is not needed to touch, but check multimeter values to determine which additional wire going to sprite detection and which is trigger :bomb: And yes, I agree with P and everyone else, colour is not per se any indicator unless totally stated. :)
You need D3 and D4,if you do have the 2 extra wires try and strip them off and like Retrospectives said,use a multimeter,hopefully this works but if it doesn't then move the other 3 wires like clock 1 over to clock 2.
Yes light gun sprite/light detection and trigger data are using D3 and D4 lines respectively, so those are most likely the two missing lines on your adapter (normal controllers doesn't use them). I'm pretty sure the light gun doesn't use DATA(x) but I don't know if it needs the CLOCK(x) line. If it does, you need to wire your adapter so it matches the controller 2 in the diagram, and controllers will no longer work with it as a result.
GND, +5V and LATCH are indeed the same on both controllers and doesn't need to be touched.
Also, I think the diagram pictures the port side of all connectors (which means the NES plug end of your adapter will be mirrored).
Quote from: P on March 14, 2018, 06:11:36 am
GND, +5V and LATCH are indeed the same on both controllers and doesn't need to be touched.
Also, I think the diagram pictures the port side of all connectors (which means the NES plug end of your adapter will be mirrored).
Yes, and since he have ground and +5V etc already in place it should be easy to figure out which wire needs to go corresponding pin as in then he just use the GND and +5V as references to know how reading the diagrams. :)
Just want to say thank you. And I need to start coming here again more. This really is one of the best and most helpful forums out there.
Quote from: Vinnk on March 14, 2018, 07:17:41 am
Just want to say thank you. And I need to start coming here again more. This really is one of the best and most helpful forums out there.
+1
As Japanese native I sometimes find other forum jargon very harsh and sometimes even cynical or maybe I cannot understand totally. But here on FW is usually not any drama and people are so friendly and helpful to each other and no matter new or old member, I feel there is totally a good calm down vibe here which in many ways are unique among gaming forums. :) Maybe because our origins are so diverse. From USA-Thailand-Taiwan-Sweden-Switzerland-Croatia-Bulgaria-Russia-Japan etc etc is important to have a more laid back understanding of having a calm down mindset, and that's what I love about FW.
I agree, it's a small forum but a very friendly one. Nothing like Nintendo Age or PC Engine FX.
Although I think Nesdev is similarly friendly it is mostly a technical forum and discussions tend to get very technical.
Yeah, this place is wonderful! I got some very good feedback a while ago about how the controller expansion works with different games. It was wonderful to try out some scenarios and share the findings with people who not only understood what I was talking about, but had insight into what I could do next. And you've all been very kind to Vinnk and myself. Oh the mistakes we could have avoided in our videos if we's Only come here more often!
This EXT port thing is extremely interesting to me, because I can see how much of an improvement the NES hardware was in that respect. Sure, it lost the microphone input hat almost nothing used, but it turns out being able to use any controller for Player 1 or 2 without an adapter on the Famicom was literally impossible. The releasing the AV Famicom makes a lot more sense now -- especially in light of its origins as a backwards compatible device for the Super Famicom. Which makes it a little surprising (but not too surprising) that none of the other EXT pins are routed through the AV Famicom P2 port, because it still has a full EXT port, and the only devices that used an NES-style plug were the controllers that came with it.
Thanks again to you all. This has been really great.
If you do the mod don't forget to report your results. Many are interested how things turn out. I wanna know if the CLOCK(x) line is used by the Zapper as well.
Quote from: SeanOrange on March 16, 2018, 12:59:28 pm
Oh the mistakes we could have avoided in our videos if we's Only come here more often!
So come here more often. :)
Oh, absolutely! I'll go through the process of just hooking up those two wires to see if they work before I disconnect the existing ones, then we will know for absolutely certain what is required and what is not. I definitely gotta give back, and not just take!
Yeah, coming by more often is definitely a thing I will be doing!
Hey guys,
I would like to re ignite that topic. I been doing some research on the Famicom controller 2 (with mic of course).
And that topic just made me take back my project to make a Famicom P2 controller work on an NES.
I found diagrams after diagrams but could not make my controller work ( i'm no even trying to make the mic work).
Here is what I did:
I looked at pinout for famicom P2 and nes here is what i done to connect it.
1: ground: red
2: clock: white / 5:+5v : brown
3: latch: yellow / 6: D3: ( mic but not connected) : blue
4: data : orange / 7: D4: none
I tested it on double dragon 2 and the only thing that happen is that the P2 character is jumping when i plug the controller. If I wiggle the connector it punch and jump.
otherwise using the pad does not make my character move or anything.
I don't know if this is the right place to post that but I thought it was related to the topic. Let me know If I should move it somewhere else.
:)